Search results

Here is a recent video that might be of interest to you. https://www.youtube.com/watch?v=NWdCtwJm6nA https://www.youtube.com/watch?v=NWdCtwJm6nA Emery Stora 77 Kingsley Frederick, CO

Still check the grounds or put a smaller resistor in the circuits. Emery Stora > > > LED lights, Emery, hard wired, no sockets. Good advice, otherwise. :) > ron > > > On Mon, 24 Sep 2018 18:08:32 -0500 Emery Stora via Gmclist >> Check the grounds from the lights and try cleaning the...

Check the grounds from the lights and try cleaning the inside of the bulb contacts. Probably a corrosion problem. Emery Stora > > > Anybody know how the floor light wiring is routed from the switch by the > door in a 1978 Eleganza?? > > I have very dim LED floor lights, and they only have...

It is: Bob Dunahugh 4441 Deer View Road Cedar Rapids, Iowa, USA 52411 319-521-4891 (mobile) yenko108 Emery Stora 77 Kingsley Frederick, CO > > Thank you Mike Kelly for contacting Bod Dunahugh. That sounds great. Do you have the e-mail address of Bob? That would be more comfortable for us >...

Stevc I recently had much the same problem. My Onan would start and run for a small time and then stall. I found that if I chocked it the ONAN would continue to run (but not well). First I thought it might be the oil level but it checked full. Then I used a jumper from 9 to 5 to bypass my...

Tom That was an aftermarket item years ago but they didn’t sell enough to stay in business very long. Emery Stora > > There was also a 'towing' version of the transmission pan. I have only seen a photo of this variant. The photo showed a deeper pan with tubing running > front to back...

I recently bought a locking device for the end of my grease gun hose This really works great for greasing the GMC You just depress the lever and it locks onto the grease fitting, allowing one to use two hands to pump the gun.. I wish I’d had this years ago.. I also bought their silicone...

I just bought a Suburban control board on Amazon for Bill Bramlett. They have a universal board made by Suburban which was about $15 less than the Dinosaur board. It worked well but he had to drill one new mounting hole. It fits about a dozen different Suburbans. Emery Stora 77 Kingsley...

No, but you can plug the top and drill and tap the bottom of some new faucets. Emery Stora 77 Kingsley Frederick, CO > > I do not think there is a replacement faucet. You have to rebuild the oem. > > All replacements seem to not have shower feed come under sink. The shower line feed is on...

Ken, I’ll take one of the cores. I’ll get it from you next spring in Tallahassee. You can tell me the cost at that time. Thanks. Emery Stora 77 Kingsley Frederick, CO > > Does anyone REALLY want a well rebuilt starter? I've got several cores -- > don't know off-hand how many. And a local...

It sounds to me that the module is going bad. Emery Stora 77 Kingsley Frederick, CO > > I've got a 6 gal Atwood LP hot water heater. I turn it on and it lights and runs for about 5 seconds. Shuts off for 3-4 seconds and restarts. Does > this maybe 5 times and stops. Gotta turn it off and it...

As the motors get older the bearings get stiffer and dry out they sometimes draw more amps especially to start turning. You might try stepping up to a 20 amp fuse. Emery Stora 77 Kingsley Frederick, CO > > Goes from the HS fan relay, through a 15a fuse, to the alt output (or visa versa)...

Peer Are you confusing the molds with possibly gas tank molds? They are talking about molds of body parts perhaps 20 feet or more long. Emery Stora > >> What would it cost to have someone who knew what they were doing meet >> up with the molds and get a really good scan of each and reduce...

Matt The depths of which tanks? I didn’t see a previous on the GMNnet referring to those tanks. Which tanks are they and what is the depth? Emery Stora > > The depth of those tanks is real close, but you would need to install 2 pair. > > OK, Left main then right main then left auxiliary and...

Chuck Garton added a third tank a few years ago. He added a standard 25 gallon GMC tank by moving a crossmember and MO tying it forward. The third tank was just in front of the aux tank. I believe there is a write up on the GMCWS web site. Emery Stora 77 Kingsley Frederick, CO > > The...

The nice thing about plastic is that it is simple to modify the molds to incorporate baffles, return line connections, indentations in the bottom for pump wells, etc. with no additional cost when making the tank. I would think it would be much more expensive and time consuming to use a 3D...

There are thousands of different plastics. Some will stand up to gasoline and ethanol. There are many very expensive ones that totally hold up but you’d have to refinance your motorhome (or house) to buy them. Fortunately a good plastic is cross linked high density polyethylene (HDPE). Both the...

I should have said Rob MUELLER. Emery > Begin forwarded message: > > From: Emery Stora via Gmclist > Subject: [GMCnet] Happy Birthday Rob > Date: September 1, 2018 at 10:01:03 AM MDT > To: gmclist > Cc: Emery Stora > Reply-To: gmclist > > Happy Birthday (tomorrow) Rob. > May you have many...

Happy Birthday (tomorrow) Rob. May you have many more and hope you are celebrating your day. We have all enjoyed your friendship. Emery Stora 77 Kingsley Frederick, CO

I thought that was pretty much put to rest back in 1998 when the FTC filed charges against the maker of Slick 50 for misleading claims and fabricating tests. They did the same thing against STP about the same time. Emery Stora 77 Kingsley Frederick, CO > > I'm a true believer in Slick 50...