Onan fuel line is very old

As soon as you start to crank the ONAN, the solenoid fuel shut off makes
one "click" and then the resulting output voltage at the control board
provides the 12 volt D.C. for it to remain pulled. When the Onan is turned
off, no 12 volts D.C on the board, and the solenoid plunger retracts,
making another "click". Usually so much noise associated with starter and
related stuff, that those clicks are hard to hear. Easier to hold on to the
thing and feel them, than to hear them.
Jim Hupy
Salem, Oregon
.

> Yeah, still poking away at the generator in between other jobs. Anyhow,
> while cranking it over found out it also needs a muffler.
> Good point about the fuel level. I'll probably leave it until I get more
> fuel, it's a backburner project anyway.
> What I would like to know if what is the normal sounds to hear when
> priming the system? I got the fuel pump thumping/ticking, but never
> felt/heard
> the solenoid valve click. Is the pump supposed to stop thumping once it
> reaches pressure?
>
>

> > Still on the Onan gas line. Just for grins and giggles, blow some air
> back
> > through your new hose, just to verify that you actually have a fuel level
> > high enough in the rear tank to cover up the end of the hose. The pump
> will
> > not account for a low fuel level in the tank. I don't care what your gage
> > says.
> > Jim Hupy
> > Salem, Oregon
> >

> >

> > >> If the H4 Amp draw is much higher than stock, lights may start to
> cycle
> > > off after a while when the dash breaker switch starts to do it’s
> job. I
> > >> say this because you don’t mention a relay loom kit.
> > >
> > > I just have regular bulbs in there, I think 55 watt.
> > >
> > > --
> > > Burl Vibert
> > > Kingston, Ontario
> > > 1976 GMC 26 foot, don't know the model
> > > _______________________________________________
> > > GMCnet mailing list
> > > Unsubscribe or Change List Options:
> > >
> > _______________________________________________
> > GMCnet mailing list
> > Unsubscribe or Change List Options:
>
>
> --
> Burl Vibert
> Kingston, Ontario
> 1976 GMC 26 foot, don't know the model
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
>
 
> Yeah, still poking away at the generator in between other jobs. Anyhow, while cranking it over found out it also needs a muffler.
> Good point about the fuel level. I'll probably leave it until I get more fuel, it's a backburner project anyway.
> What I would like to know if what is the normal sounds to hear when priming the system? I got the fuel pump thumping/ticking, but never
> felt/heard the solenoid valve click. Is the pump supposed to stop thumping once it reaches pressure?

Burl,

If I hold that solenoid valve I can usually feel it, I would say I can't hear, my hearing is a little better than KenB's.
The pump will click pretty fast until it gets to pressure, then it slows down a lot. If you can hear it were your prime switch is, don't even bother
cranking until it slows down. If you have doubts about that valve, take it out. While the APU package was designed for GMC, it was sold to other
coach builders and many of those had a possible fuel level that was above the carburetor, thus requiring a solid shut off for safety. One of the BFs
in my collection seems to never have had one.

Good luck on a muffler, I know JimK has them (of course), but if you find a small engine shop in Canada, they might be able to help. Unfortunately,
that specific version of Onan was not very common in stand alone power.

Matt
--
Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL, GMCES
Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum Brakes with Applied Control Arms
SE Michigan - Near DTW - Twixt A2 and Detroit
 
Still poking away at that Onan in my spare time.
Finally getting gas to the carb, pretty sure the fuel shutoff wasn't opening.

Problem now is this:

https://postimg.cc/jws2DmgJ

Looks like someone didn't have a gasket, so tried to make one. I hope the goo isn't all through the carb.
Can I get a gasket at a local small engine shop, or do I add that to my list?
--
Burl Vibert
Kingston, Ontario
1976 GMC 26 foot, Sheridan reno, don't know original model
 
Yes the gasket is part of the fuel filter kit I referened before from NAPA.
--
Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana
 
> Yes the gasket is part of the fuel filter kit I referened before from NAPA.

This gasket I need now is for the carb float bowl, not the filter. Looks like someone tried to seal it with some goo that's not quite compatible with
gas or something.
I found a kit in the parts list, ONAN 146-0185, I'll see if I can get it locally, if not, I'll add it to the list I'm making for JimK as he has the
gasket by itself for sale.

I also found out the screw at the bottom of the carb bowl is not a drain like in other carbs, it's basically the main jet adjustment.

--
Burl Vibert
Kingston, Ontario
1976 GMC 26 foot, Sheridan reno, don't know original model
 
Sorry, I misunderstood again...Ken B.
--
Ken Burton - N9KB
76 Palm Beach
Hebron, Indiana
 
> This gasket I need now is for the carb float bowl, not the filter. Looks like someone tried to seal it with some goo that's not quite compatible
> with gas or something.
> I found a kit in the parts list, ONAN 146-0185, I'll see if I can get it locally, if not, I'll add it to the list I'm making for JimK as he has
> the gasket by itself for sale.
>
> I also found out the screw at the bottom of the carb bowl is not a drain like in other carbs, it's basically the main jet adjustment.

Burl,

Two things here.
If you have the gasket in there, you can use that as a drain, just don't turn the screw that is in that plug.

If JimK does not have that gasket (or you want it sooner), that carburetor is an Walboro LMB and they were used all over. Find any small engine shop
and he probably has a bunch hung on a nail.

Good luck cleaning off the RTV.

Matt
--
Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL, GMCES
Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum Brakes with Applied Control Arms
SE Michigan - Near DTW - Twixt A2 and Detroit
 
I bought a rebuild kit for mine off of ebay worked great 👍

> > This gasket I need now is for the carb float bowl, not the filter.
> Looks like someone tried to seal it with some goo that's not quite
> compatible
> > with gas or something.
> > I found a kit in the parts list, ONAN 146-0185, I'll see if I can get it
> locally, if not, I'll add it to the list I'm making for JimK as he has
> > the gasket by itself for sale.
> >
> > I also found out the screw at the bottom of the carb bowl is not a drain
> like in other carbs, it's basically the main jet adjustment.
>
> Burl,
>
> Two things here.
> If you have the gasket in there, you can use that as a drain, just don't
> turn the screw that is in that plug.
>
> If JimK does not have that gasket (or you want it sooner), that carburetor
> is an Walboro LMB and they were used all over. Find any small engine shop
> and he probably has a bunch hung on a nail.
>
> Good luck cleaning off the RTV.
>
> Matt
> --
> Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL,
> GMCES
> Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum
> Brakes with Applied Control Arms
> SE Michigan - Near DTW - Twixt A2 and Detroit
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
>
 
Here's a link to what I used
https://www.ebay.com/sch/i.html?_nkw=k1-lmb

> I bought a rebuild kit for mine off of ebay worked great 👍
>

>

>> > This gasket I need now is for the carb float bowl, not the filter.
>> Looks like someone tried to seal it with some goo that's not quite
>> compatible
>> > with gas or something.
>> > I found a kit in the parts list, ONAN 146-0185, I'll see if I can get
>> it locally, if not, I'll add it to the list I'm making for JimK as he has
>> > the gasket by itself for sale.
>> >
>> > I also found out the screw at the bottom of the carb bowl is not a
>> drain like in other carbs, it's basically the main jet adjustment.
>>
>> Burl,
>>
>> Two things here.
>> If you have the gasket in there, you can use that as a drain, just don't
>> turn the screw that is in that plug.
>>
>> If JimK does not have that gasket (or you want it sooner), that
>> carburetor is an Walboro LMB and they were used all over. Find any small
>> engine shop
>> and he probably has a bunch hung on a nail.
>>
>> Good luck cleaning off the RTV.
>>
>> Matt
>> --
>> Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL,
>> GMCES
>> Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum
>> Brakes with Applied Control Arms
>> SE Michigan - Near DTW - Twixt A2 and Detroit
>> _______________________________________________
>> GMCnet mailing list
>> Unsubscribe or Change List Options:
>>
>
 
> that carburetor is an Walboro LMB and they were used all over. Find any small engine shop and he probably has a bunch hung on a nail.
>
> Matt

Just wanted to point out a difference I've found in American vs Canadian service.

I contacted or went to 4 different small-engine shops locally. None of them had parts, none would even look up or order parts, let alone having a
bunch hung on a nail. They just said they don't deal with ONAN and told me to order parts online. Canadians might be friendly, but I've found in
some services, we don't try very hard.

--
Burl Vibert
Kingston, Ontario
1976 GMC 26 foot, Sheridan reno, don't know original model
 
> Just wanted to point out a difference I've found in American vs Canadian service.
>
> I contacted or went to 4 different small-engine shops locally. None of them had parts, none would even look up or order parts, let alone having
> a bunch hung on a nail. They just said they don't deal with ONAN and told me to order parts online. Canadians might be friendly, but I've found
> in some services, we don't try very hard.

Burl,

I guess that is why I have clients still calling me when I officially closed the shop 5 years ago.
When in my barn next, I will see if I still have a kit there. If I do, I could put that gasket in an envelope and mail it to you in standard mail.

Matt
--
Matt & Mary Colie - Chaumière -'73 Glacier 23 - Members GMCMI, GMCGL, GMCES
Electronically Controlled Quiet Engine Cooling Fan with OE Rear Drum Brakes with Applied Control Arms
SE Michigan - Near DTW - Twixt A2 and Detroit
 
> > Just wanted to point out a difference I've found in American vs Canadian service.
> >
> > I contacted or went to 4 different small-engine shops locally. None of them had parts, none would even look up or order parts, let alone
> > having a bunch hung on a nail. They just said they don't deal with ONAN and told me to order parts online. Canadians might be friendly, but
> > I've found in some services, we don't try very hard.
>
> Burl,
>
> I guess that is why I have clients still calling me when I officially closed the shop 5 years ago.
> When in my barn next, I will see if I still have a kit there. If I do, I could put that gasket in an envelope and mail it to you in standard
> mail.
>
> Matt

Thanks Matt, but that's ok. I can order one online, I was just trying to source locally and wanted to vent.
--
Burl Vibert
Kingston, Ontario
1976 GMC 26 foot, Sheridan reno, don't know original model
 
You must log in or register to reply here.
Get your shine on at www.cruzingear.co
Applied GMC

Share this page

Share this page
Top Bottom
Back