Headliner

T

tmsnyder

Well-known member
Jan 15, 2014
3,351
1,241
113
Buffalo NY
Apologies, this is probably covered somewhere but I had no luck with the search engine. Is there a DIY way to re-do the interior headliner and walls
with something that is close to 'factory'?

I'm thinking that the panels can be cut from a hard board material similar to the original, then covered with a headliner material such as this:

http://www.jjautofabrics.com/enduratex-vinyl-headliner-classic-premier-perforated-1181-white-54/

maybe even with a layer of foam under the vinyl?

Can you point me to a reference on how to do this? Thanks
--
Todd Snyder, Buffalo NY
1976 Eleganza II
 
I used that stuff too, I like it, but you have to be careful not to over tighten your screws as it dents easy.
But it feels good and took adhesive well.
Remember to use high temperature headliner adhesive or the glue will fail!
________________________________
From: Gmclist on behalf of Larry via Gmclist
Sent: Wednesday, May 1, 2019 9:56 AM
To: gmclist
Cc: Larry
Subject: Re: [GMCnet] Headliner

I used this stuff. Stiff, waterproof and added a R3 insulation. JWID

http://www.gmcmhphotos.com/photos/new-ceilings-or-headliner/p16870.html
http://www.gmcmhphotos.com/photos/new-ceilings-or-headliner/p16869.html
--
Larry
78 Royale w/500 Caddy
Menomonie, WI.

_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
 
Hi Todd,

Headliner fabric is an easy-to-work-with product. It typically already has a foam layer attached to the back (I am cautious about using the word
"always").

Yes, it can be glued to hardboard using something like this (has to have a high tolerance for heat):
https://www.autozone.com/sealants-glues-adhesives-and-tape/headliner-adhesive/3m-headliner-and-fabric-adhesive/110464_0_0#

The adhesive is a "contact" style glue, so you will "unroll" the fabric on to the backing and then roll over it with a small roller (available in the
carpet installation section at Home Depot). The foam backing and lightweight nature of the fabric makes it easy to work with. Just let it find its
own, unstretched and unscrunched, shape as it is rolled on to the backing.

For my pickup, the backing is higher density cardboard card stock, and it is just fine. This stuff is sold in upholstery shops to make door panels.
Lightweight, and the good stuff is waterproof:
https://www.miamicorp.com/products/SUPPLIES%20@@26%20TOOLS/DOOR%20PANEL%20BOARD/COWLBOARD.aspx
https://www.miamicorp.com/default.aspx?page=item+detail&itemcode=CB7W&catlist=280&parent=2311

Good luck with your project,

Tom Newell
San Pedro, California
--
Proud Citizen of
Los Angeles, California
Founded 1781 as
El Pueblo de la Reyna de los Angeles, Alta California
 
> I used that stuff too, I like it, but you have to be careful not to over tighten your screws as it dents easy.
> But it feels good and took adhesive well.
> Remember to use high temperature headliner adhesive or the glue will fail!
> ________________________________
> From: Gmclist on behalf of Larry via Gmclist
> Sent: Wednesday, May 1, 2019 9:56 AM
> To: gmclist
> Cc: Larry
> Subject: Re: [GMCnet] Headliner
>
> I used this stuff. Stiff, waterproof and added a R3 insulation. JWID
>
> http://www.gmcmhphotos.com/photos/new-ceilings-or-headliner/p16870.html
> http://www.gmcmhphotos.com/photos/new-ceilings-or-headliner/p16869.html
> --
> Larry
> 78 Royale w/500 Caddy
> Menomonie, WI.
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org

This is the stuff I glued to the Duro Therm.
https://www.dltcorporation.com/category_s/343.htm

--
Larry
78 Royale w/500 Caddy
Menomonie, WI.
 
That's cool stuff but I kind of like the look of the original 'snakebite' in the link I posted above.
--
Todd Snyder, Buffalo NY
1976 Eleganza II
 
Todd,
The snakebite fabric goes over the plastic cardboard stuff, you either have to glue down some foam, then you fabric, or if youre lucky the foam is already attached.
________________________________
From: Gmclist on behalf of Todd Snyder via Gmclist
Sent: Friday, May 3, 2019 1:24 PM
To: gmclist
Cc: Todd Snyder
Subject: Re: [GMCnet] Headliner

That's cool stuff but I kind of like the look of the original 'snakebite' in the link I posted above.
--
Todd Snyder, Buffalo NY
1976 Eleganza II

_______________________________________________
GMCnet mailing list
Unsubscribe or Change List Options:
http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
 
From what I've read plus some personal experience, quite a few "Headliner Adhesives" don't hold up well to very hot climates... I've used the 3M one,
and it only lasted about a year or so down here in Texas....

When it failed, I did some more research and read that a lot of pros use a product called "Weldwood Landau Top and Trim Adhesive"

FWIW, I redid the failed 3M headliner with this stuff, and it is still going strong several years later...

https://www.dap.com/dap-products-ph/weldwood-landau-top-trim-high-heat-resistant-contact-cement/

You can find it in quarts, gallons and 5 gallon pails depending on how much you need.... One tip to keep in mind: you're probably going to want to
wear a respirator, especially if you are spraying it...
--
Mark S. '73 Painted Desert,
Manny 1 Ton Front End,
Howell Injection,
Leigh Harrison 4bag and Rear Brakes,
Fort Worth, TX
 
That looks sweet Carl.

Sully
Bellevue wa.

On Fri, May 3, 2019 at 5:05 PM Carl Stouffer via Gmclist <

> I really like the way my PO did mine:
>
> http://www.gmcmhphotos.com/photos/g3244-headliner-installation.html
> --
> Carl Stouffer
> '75 ex Palm Beach
> Tucson, AZ.
> Chuck Aulgur Reaction Arm Disc Brakes, Quadrabags, 3.70 LSD final drive,
> Lenzi knuckles/hubs, Dodge Truck 16" X 8" front wheels, Rear American
> Eagles,
> Solar battery charging. GMCSJ and GMCMI member
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
 
> That looks sweet Carl.
>
> Sully
> Bellevue wa.
>
> On Fri, May 3, 2019 at 5:05 PM Carl Stouffer via Gmclist <

>
> > I really like the way my PO did mine:
> >
> > http://www.gmcmhphotos.com/photos/g3244-headliner-installation.html
> > --
> > Carl Stouffer
> > '75 ex Palm Beach
> > Tucson, AZ.
> > Chuck Aulgur Reaction Arm Disc Brakes, Quadrabags, 3.70 LSD final drive,
> > Lenzi knuckles/hubs, Dodge Truck 16" X 8" front wheels, Rear American
> > Eagles,
> > Solar battery charging. GMCSJ and GMCMI member
> >
> > _______________________________________________
> > GMCnet mailing list
> > Unsubscribe or Change List Options:
> > http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
> >
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org

Thanks Todd,

One of the things I like about it is that the center drop section can be taken down easily in order to run new wiring etc. The other thing is the
acoustics. The fabric (hull liner) makes the inside of the coach nice and quiet.

--
Carl Stouffer
'75 ex Palm Beach
Tucson, AZ.
Chuck Aulgur Reaction Arm Disc Brakes, Quadrabags, 3.70 LSD final drive, Lenzi knuckles/hubs, Dodge Truck 16" X 8" front wheels, Rear American Eagles,
Solar battery charging. GMCSJ and GMCMI member
 
I noticed the same thing (quiet) when I took down the oe vinyl covered
plywood and put up foam backed fabric in The War Pig.
Good stuff.

Sully
Bellevue wa

On Sat, May 4, 2019 at 9:07 PM Carl Stouffer via Gmclist <

> > That looks sweet Carl.
> >
> > Sully
> > Bellevue wa.
> >
> > On Fri, May 3, 2019 at 5:05 PM Carl Stouffer via Gmclist <

> >
> > > I really like the way my PO did mine:
> > >
> > > http://www.gmcmhphotos.com/photos/g3244-headliner-installation.html
> > > --
> > > Carl Stouffer
> > > '75 ex Palm Beach
> > > Tucson, AZ.
> > > Chuck Aulgur Reaction Arm Disc Brakes, Quadrabags, 3.70 LSD final
> drive,
> > > Lenzi knuckles/hubs, Dodge Truck 16" X 8" front wheels, Rear American
> > > Eagles,
> > > Solar battery charging. GMCSJ and GMCMI member
> > >
> > > _______________________________________________
> > > GMCnet mailing list
> > > Unsubscribe or Change List Options:
> > > http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
> > >
> > _______________________________________________
> > GMCnet mailing list
> > Unsubscribe or Change List Options:
> > http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
> Thanks Todd,
>
> One of the things I like about it is that the center drop section can be
> taken down easily in order to run new wiring etc. The other thing is the
> acoustics. The fabric (hull liner) makes the inside of the coach nice and
> quiet.
>
> --
> Carl Stouffer
> '75 ex Palm Beach
> Tucson, AZ.
> Chuck Aulgur Reaction Arm Disc Brakes, Quadrabags, 3.70 LSD final drive,
> Lenzi knuckles/hubs, Dodge Truck 16" X 8" front wheels, Rear American
> Eagles,
> Solar battery charging. GMCSJ and GMCMI member
>
> _______________________________________________
> GMCnet mailing list
> Unsubscribe or Change List Options:
> http://list.gmcnet.org/mailman/listinfo/gmclist_list.gmcnet.org
>
 
A friend put FRP on the ceiling and his wife was constantly complaining about noise from the engine fan, etc. I notice when it comes on, but it is
not annoying at all. The coach is nice and quiet and comfortable.
--
Carl Stouffer
'75 ex Palm Beach
Tucson, AZ.
Chuck Aulgur Reaction Arm Disc Brakes, Quadrabags, 3.70 LSD final drive, Lenzi knuckles/hubs, Dodge Truck 16" X 8" front wheels, Rear American Eagles,
Solar battery charging. GMCSJ and GMCMI member
 
You must log in or register to reply here.
Applied GMC
GMCMI Fall 2026 Rally

Share this page

Share this page
Top Bottom
Back