Search results

Yes but you have to work the belts around the fan blades. There is usually one place where the fan shroud has a little bit of clearance so you can work the belt in over the blades without taking off the shroud. Just lean in over the top of the engine to do it. Emery Stora 77 Kingsley...

Go back and read my reply on March 15. I said: “The center of the hose connection/ switch on the face of the panel is 17” from the floor and 15-3/8” from the face of the cabinet. The vacuum cabinet is mounted inside the cupboard opposite the hose connection. “ I sometimes feel people don’t...

Tom I would recommend the Jabsco. It is a strong pump and the only problem I’ve had is long hair (ladies) getting wound around the impeller. I finely added an extra valve just in front of the pump and used a rubber connector to the pump so I could remove it quickly. It always seemed to stop just...

But, who has ABS holding tanks in their GMC? As I just posted in another message our tanks are polypropylene, not ABS. Emery Stora 77 Kingsley Frederick, CO > > For those of you who have experienced cracks or breaks in your black ABS holding tank take a look at page 24 of the April 2019...

There are some excellent, easily accessible campsites in Big Bend. Don’t try to camp at the ones you mention. When I get back home from the GMCMI rally in Tallahassee I can look up the campground that we have stayed at there and even give you some campsite numbers of pull through sites that...

However the original GMC holding tanks are made of polypropylene which is not ABS. I really don’t think any of them are ABS unless someone got an ABS replacement tank. So I am really questioning if this repair would work on the GMC tanks. Emery Stora 77 Kingsley Frederick, CO > > GMC group...

That was written by our current President of GMCMI He did an excellent job of rebuttal without ruffling any one. Emery Stora 77 Kingsley Frederick, CO On the way to Tallahassee > > Here you go Todd. > >...

Larry You are making some assumptions that are incorrect. Also, I really don’t need you to tell me that I’m an asshole because I didn’t read a message. Emery Stora > >>> Matt and Emery, >>> It should be noted that the following went out in an email to every attendee that was registered as...

I also use heavy duty 3/4” garden hose. I bought a 50’ at Home Depot. I cut it in half and fastened the cut end to the macerator through a 3/4” to 1/2” adapter. Don’t let the Home Depot plumbing dept tell you they don’t have the adapter. It’s not in Plumbing. You’ll find it in the lawn sprinkler...

Doug — Plus the many friends you make. Michelle and I are looking forward to seeing you and Virginia again the next time we go through Lincoln. Unless we meet again at a rally before then. Emery Stora > > Thanks for the warm welcome Matt. > But I know you. I know all you guys, I’ve been...

Too late. I’m in. Georgia. I have hose and electric cord but not much blocking. We can probably find some at Home Depot if a lot of people need it Emery > > Just wanted to let attendees know that this is a fairgrounds and not a > campground. It is advisable to bring additional electric...

The center of the hose connection/ switch on the face of the panel is 17” from the floor and 15-3/8” from the face of the cabinet. The vacuum cabinet is mounted inside the cupboard opposite the hose connection. Emery Stora 77 Kingsley Frederick, CO > > In our 78 Palm Beach it was on the...

Len You can take that switch apart and clean up the terminals. Then put in some dielectric grease to keep out moisture and stop corrosion. I did this to mine and the switch worked fine afterwards. Emery Stora 77 Kingsley Frederick, CO Emery > > No parts available,,,,,,,,,,,,,,,,, > > Len...

I did my garage and workshop with RustOleum Epoxyshield from Home Depot. It has held up well now for 5 years. Do a small area at a time. The areas will blend well. It is a two part system. If you mix too much it will cure before you get it down. DON’T USE IT IF IS HAS STARTED TO THICKEN. It...

My local Autozone carries an assortment if copper washers in a box behind the counter. Some are flat and some are dished to seal on brass fittings. Emery Stora > > https://thenorcoldguy.com/ > >> Went to fire up the fridge today, would not light and when it did it cut out >> immediately...

I have noticed that all GMCnet messages say: from Adrien Genesoto via Gmclist and when I send a message it shows: To: Adrien Genesoto via Gmclist I am not sure who Adrien Genesoto is and why the name shows up on all my emails? Can anyone explain this to me? Emery Stora 77 Kingsley Frederick, CO

You might drill out the rivets that hold the case together. It might have gotten a voltage spike. This can sometimes burn a MOV. The Metal Oxide Varistor or MOV is a voltage dependent, nonlinear device that provides excellent transient voltage suppression. The Metal Oxide Varistor is designed to...

I believe that it was Alex Sirum GMC that came up with this several years ago. You might check with Jeff Sirum. Emery Stora > > I thought that I had pictures of the device, but alas no. It was a 2” sched 40 pipe 10 foot long welded to a old rim center section so that it could bolt up to the...

I don’t remember for sure but I think it was 10 foot. Emery Stora > > Is that a 21-foot long pipe? > > On Mon, Mar 4, 2019 at 10:21 AM Ken Henderson via Gmclist < > >> Hal, >> >> I suppose you're concerned, as I would be, about using the back of the >> reaction arm's torque box as a...

Ken We are going to Perry but could come to the farm first if there are going to be others there going to Perry. That way we could all park together at Perry. Do you have a count of GMCs going to Perry? Otherwise we’ll just go to the farm after Perry Emery Stora > > OK, it's time to take a...