Statkus Engines
- Thread starter al chernoff
- Start date
Hahaha
Sounds good to me Al. Thanks for the compliments.
bdub
>Bdub, on western states has updated the newsletters. Billy is doing a great
>job. Think we should give him a 10% an increase in pay, lets see 10% of 0 is?
>... How about that Billy?
>al
>
>
> > where are the news letters on bdubs??
> >
> > is it on western states ??
> >
> > gene
> >
> > >For those of you who were in Albuq for the Balloon Fiesta Roundup, a great
> > >presentation on engines was presented by Jim Statkus. He has a beautiful
> > RV and
> > >motor rebuilding place in Albuq. He is the one who did my engine, and the
> > >presentaton he gave was excellent. I asked him to give us some info for
> > anyone
> > >who wanted to have an engine done.. He offers the following.
> > >
> > >If you send in the engine, the cost is $2850, and if you want him to do
> > the R&R
> > >it will be another $3K. Here is what he does in any rebuild.
> > >
> > >The Statkus Engine's RV Series Rebuild
> > >
> > >The Statkus rebuild is better than other engine rebuilds for many reasons.
> > >Statkus Engines rebuilds an engine one way, we do not have levels of
> > rebuilds.
> > >Our standard high-energy engine is built around 8.75:1 compression
> ratio ? We
> > >find this is the best ratio with the gas that is available today. We not
> > only
> > >rebuild the engine, but we do the removal and installation too! We can
> > also do
> > >other maintenance work like brakes, transmissions and much more.
> > >
> > >Block
> > >Align Hone
> > >Bored
> > >Honed to size using 3 grits of stones
> > >Decked & squared
> > >Fitted with new cam bearings, freeze plugs & oil gallery plugs
> > >
> > >Heads
> > >3 Angle Valve Job
> > >Hard Seats for Unleaded Fuel
> > >Manganese-Bronze Guides
> > >Milled for correct seal
> > >
> > >Connecting Rods
> > >Resized
> > >Pin ends check for size
> > >
> > >Crankshaft
> > >Precision ground
> > >Oil holes chamfered
> > >Micro-Polished
> > >
> > >Assembly
> > >Electronically Balanced
> > >* Ensures a vibration free engines!
> > >Internal Parts
> > >
> > >Only high quality parts are used!
> > >Fel-Pro Gaskets
> > >Silvo-Lite Pistons
> > >Seal Power Moly Rings
> > >Clevite Bearings
> > >Johnson Lifters
> > >Melling RV High Energy Torque Camshaft
> > >Seal Power Push rods
> > >Melling oil pump
> > >
> > >You can read the write-up in Bdubs web page under newsletters.
> > >
> > >If you are interested call him at 505-881-4250, or fax him at the same
> > number.
> > >
> > >If you want to email him, send email to wstatkus
> > >
> > >
> > >
> > >
> > Genef -- 77PB/ore/ca
> > GMC MOTORHOME INFORMATION
> > mr.erf
> > http://www.california.com/~eagle/
Sounds good to me Al. Thanks for the compliments.
bdub
>Bdub, on western states has updated the newsletters. Billy is doing a great
>job. Think we should give him a 10% an increase in pay, lets see 10% of 0 is?
>... How about that Billy?
>al
>
>
> > where are the news letters on bdubs??
> >
> > is it on western states ??
> >
> > gene
> >
> > >For those of you who were in Albuq for the Balloon Fiesta Roundup, a great
> > >presentation on engines was presented by Jim Statkus. He has a beautiful
> > RV and
> > >motor rebuilding place in Albuq. He is the one who did my engine, and the
> > >presentaton he gave was excellent. I asked him to give us some info for
> > anyone
> > >who wanted to have an engine done.. He offers the following.
> > >
> > >If you send in the engine, the cost is $2850, and if you want him to do
> > the R&R
> > >it will be another $3K. Here is what he does in any rebuild.
> > >
> > >The Statkus Engine's RV Series Rebuild
> > >
> > >The Statkus rebuild is better than other engine rebuilds for many reasons.
> > >Statkus Engines rebuilds an engine one way, we do not have levels of
> > rebuilds.
> > >Our standard high-energy engine is built around 8.75:1 compression
> ratio ? We
> > >find this is the best ratio with the gas that is available today. We not
> > only
> > >rebuild the engine, but we do the removal and installation too! We can
> > also do
> > >other maintenance work like brakes, transmissions and much more.
> > >
> > >Block
> > >Align Hone
> > >Bored
> > >Honed to size using 3 grits of stones
> > >Decked & squared
> > >Fitted with new cam bearings, freeze plugs & oil gallery plugs
> > >
> > >Heads
> > >3 Angle Valve Job
> > >Hard Seats for Unleaded Fuel
> > >Manganese-Bronze Guides
> > >Milled for correct seal
> > >
> > >Connecting Rods
> > >Resized
> > >Pin ends check for size
> > >
> > >Crankshaft
> > >Precision ground
> > >Oil holes chamfered
> > >Micro-Polished
> > >
> > >Assembly
> > >Electronically Balanced
> > >* Ensures a vibration free engines!
> > >Internal Parts
> > >
> > >Only high quality parts are used!
> > >Fel-Pro Gaskets
> > >Silvo-Lite Pistons
> > >Seal Power Moly Rings
> > >Clevite Bearings
> > >Johnson Lifters
> > >Melling RV High Energy Torque Camshaft
> > >Seal Power Push rods
> > >Melling oil pump
> > >
> > >You can read the write-up in Bdubs web page under newsletters.
> > >
> > >If you are interested call him at 505-881-4250, or fax him at the same
> > number.
> > >
> > >If you want to email him, send email to wstatkus
> > >
> > >
> > >
> > >
> > Genef -- 77PB/ore/ca
> > GMC MOTORHOME INFORMATION
> > mr.erf
> > http://www.california.com/~eagle/
