Onan carb replacement possibility

J

jerry work

New member
Feb 3, 2003
1,108
0
0
While researching for the presentation I am giving at the upcoming GMCWS Coos Bay, OR, rally on how to run your Onan on gasoline or propane at the flip of one toggle switch, I came across a TECUMSEH CARBURETOR 631828 that looks for all the world like a clone of our Onan carb but costs just $25. I have not used one personally, so can’t be sure it is the same, but it looks to me like with a minor modification to the throttle and choke linkage this might be far better, easier and cheaper than trying to rebuild what you have.

Jerry
Jerry Work
The Dovetail Joint
Fine furniture designed and hand crafted in the 1907 former Masonic Temple building in historic Kerby, OR

glwork
http://jerrywork.com
 
Jerry -

Where do I get one for 25 scoots??

--johnny

--
'76 23' transmode Norris upfit, 76 26' Eleganza(?) with beaucoup mods and add - ons.
Braselton, Ga.

"Sometimes I wonder what tomorrow's gonna bring when I think about my dirty life and times" --Warren Zevon
 
> Jerry -
>
> Where do I get one for 25 scoots??
>
> --johnny

Johnny,

Try Amazon for 18.99+shipping

There might be some challenges to adapting.

Matt - relaxing at Mansfield.
--
Matt & Mary Colie - Members GMCMI, GMCGL, GMCES
'73 Glacier 23 - Still Loving OE Rear Drum Brake with Applied Control Arms
Now with both true Keyless and remote entry
SE Michigan - Twixt A2 and Detroit
 
OK, I got one on the way. I have a Yamamamamaha set without carb, it might fit there as well. For fifteen bux I'll find out.

Thanks!

--johnny
--
'76 23' transmode Norris upfit, 76 26' Eleganza(?) with beaucoup mods and add - ons.
Braselton, Ga.

"Sometimes I wonder what tomorrow's gonna bring when I think about my dirty life and times" --Warren Zevon
 
Jerry -

Where do I get one for 25 scoots??

--johnny

--
'76 23' transmode Norris upfit, 76 26' Eleganza(?) with beaucoup mods and add - ons.
Braselton, Ga.

"Sometimes I wonder what tomorrow's gonna bring when I think about my dirty life and times" --Warren Zev
===============
 
Ordered. We'll see how it stacks up.

--johnny

--
'76 23' transmode Norris upfit, 76 26' Eleganza(?) with beaucoup mods and add - ons.
Braselton, Ga.

"Sometimes I wonder what tomorrow's gonna bring when I think about my dirty life and times" --Warren Zevon
 
Got it. Interestingly, on the top of the housing on the idle screw side there's a flat in the casting which had the maker's name or the part number.
I can't tell which.... because it's been freshly ground off. It looks identical to the one on the chinese set I put in my 23' cvoach
superficially. I'm not gonna pull it out to see exactly. The intake side looks about the same as the Onan, if the holes match it will run the Onan.
You'd need a couple of drills and taps and some machhine screws to modify the choke and throttle bellcranks, but it looks to be eminently do-able.
I'm outa here for a week and some, I'll do some measurements when I get back.

--johnny
--
'76 23' transmode Norris upfit, 76 26' Eleganza(?) with beaucoup mods and add - ons.
Braselton, Ga.

"Sometimes I wonder what tomorrow's gonna bring when I think about my dirty life and times" --Warren Zevon
 
Last edited by a moderator:
You must log in or register to reply here.
Get your shine on at www.cruzingear.co
Applied GMC

Share this page

Share this page
Top Bottom
Back