Hubs how to get them off, OTC 927

[thomas g. warner]

If you buy the front bearing puller and OTC927 the insert that comes with
the puller will do exactly that.

>Scott,
>
>The GM service procedure requires using a slide hammer to pull the hub out
>of the knuckle. You can probably use a harmonic balancer puller to push it
>out like the Thoma tool if you make a push-plate to fit inside the knuckle.
>
>Patrick
>

>>
>> Tom!
>> Thanks for the reply-- I still can't picture it--what website
>> is your puller
>> on? --I need to get a handle on what you are explaining.
>>
>> Scott
>>
>
>

 

[patrick flowers]

Exactly what? Allow the OTC927 to push the hub out of the knuckle or
allow a harmonic balancer puller to push the hub out of the knuckle?

Patrick

>
> If you buy the front bearing puller and OTC927 the insert that comes with
> the puller will do exactly that.
>

> >
> >The GM service procedure requires using a slide hammer to pull the hub out
> >of the knuckle. You can probably use a harmonic balancer puller to push it
> >out like the Thoma tool if you make a push-plate to fit inside the knuckle.
- --
Patrick Flowers
Mailtoatrick

The GMC Motorhome Page
http://www.gmcmotorhome.com

 

[bdub]

I've updated the page at:
http://www.web-access.net/~bmassey/twarner.html
to include a couple of pictures that should clear up any confusion.

hth
bdub
central Texas

>In a message dated 9/9/99 4:24:40 PM Eastern Daylight Time, warner
>writes:
>
> > If you buy the front bearing puller and OTC927 the insert that comes with
> > the puller will do exactly that.
> >
>Tom!
>
>This is what I want: If I buy your tool and an OTC-927 and I can do my
>bearings, correct? YES/NO
>
>Scott
>ADOHEN
>SUPPLY CO, OTC-927

 

[bright walter]

I am curious exactly how this happens too (getting the hub out). Also,
yes/no; you need a seal installation tool in addition to the warner bearing
tool set and the OTC 927? TIA walter bright 76 GB.

- -----Original Message-----
From: Billy Massey [mailto:bmassey]
Sent: Thursday, September 09, 1999 5:22 PM
To: gmcmotorhome
Subject: Re: GMC: Hubs how to get them off, OTC 927

I've updated the page at:
http://www.web-access.net/~bmassey/twarner.html
to include a couple of pictures that should clear up any confusion.

hth
bdub
central Texas

>In a message dated 9/9/99 4:24:40 PM Eastern Daylight Time, warner
>writes:
>
> > If you buy the front bearing puller and OTC927 the insert that comes
with
> > the puller will do exactly that.
> >
>Tom!
>
>This is what I want: If I buy your tool and an OTC-927 and I can do my
>bearings, correct? YES/NO
>
>Scott
>ADOHEN
>SUPPLY CO, OTC-927

 

[thomas g. warner]

Scott with my tool and the OTC927 you can not only service the bearings but
with the addition of a heavy U bolt can properly adjust the torsions bars,
remove the harmonic balancer and ?

>In a message dated 9/9/99 4:24:40 PM Eastern Daylight Time, warner
>writes:
>
>> If you buy the front bearing puller and OTC927 the insert that comes with
>> the puller will do exactly that.
>>
>Tom!
>
>This is what I want: If I buy your tool and an OTC-927 and I can do my
>bearings, correct? YES/NO
>
>Scott
>ADOHEN
>SUPPLY CO, OTC-927
>
>

 

[thomas g. warner]

will push the hub out of the knuckle and pull the harmmonic balancer.

>Exactly what? Allow the OTC927 to push the hub out of the knuckle or
>allow a harmonic balancer puller to push the hub out of the knuckle?
>
>Patrick
>

>>
>> If you buy the front bearing puller and OTC927 the insert that comes with
>> the puller will do exactly that.
>>

>> >
>> >The GM service procedure requires using a slide hammer to pull the hub out
>> >of the knuckle. You can probably use a harmonic balancer puller to push it
>> >out like the Thoma tool if you make a push-plate to fit inside the knuckle.
>--
>Patrick Flowers
>Mailtoatrick
>
>The GMC Motorhome Page
>http://www.gmcmotorhome.com
>
>

 

[thomas g. warner]

Walter seal installation tools are cheap but to tell you the truth i never
use them. If you are very careful you can gently tap the seals in to place.
Its how I have alway done it and never damaged one and always seat fine.
just have to be careful to keep it square to the knuckle.

>I am curious exactly how this happens too (getting the hub out). Also,
>yes/no; you need a seal installation tool in addition to the warner bearing
>tool set and the OTC 927? TIA walter bright 76 GB.
>
>-----Original Message-----
>From: Billy Massey [mailto:bmassey]
>Sent: Thursday, September 09, 1999 5:22 PM
>To: gmcmotorhome
>Subject: Re: GMC: Hubs how to get them off, OTC 927
>
>
>I've updated the page at:
>http://www.web-access.net/~bmassey/twarner.html
>to include a couple of pictures that should clear up any confusion.
>
>hth
>bdub
>central Texas
>
>

>>In a message dated 9/9/99 4:24:40 PM Eastern Daylight Time, warner
>>writes:
>>
>> > If you buy the front bearing puller and OTC927 the insert that comes
>with
>> > the puller will do exactly that.
>> >
>>Tom!
>>
>>This is what I want: If I buy your tool and an OTC-927 and I can do my
>>bearings, correct? YES/NO
>>
>>Scott
>>ADOHEN
>>SUPPLY CO, OTC-927
>
>

 

[thomas g. warner]

using the long insert and the center bolt to pull on

>In a message dated 9/9/99 6:24:00 PM Eastern Daylight Time, warner
>writes:
>
>> will push the hub out of the knuckle
>Tom!
>
>How do you fasten the OTC-927 to push/pull the hub from the knuckle?
>
>Scott NEHODA'S BACK
>YARD
>
>