Search results

Due to the crossover design of the intake manifold each injector feeds 2 cylinders on the left side and 2 cylinders on the right side. So the mixture reading by a sensor on the left side would be the same as the reading by a sensor on the right side. So, only one sensor would be needed as...

Hi Rob I don’t think our radiators would be copper because they would not have the strength needed. Think of a sword made from copper. It would easily bend and not be a good weapon. However if you add zinc or other metals to the copper you create brass or bronze. Thus the Bronze Age with strong...

> >> >> The oil lines do have a metal braided covering. They've been on the coach >> about as long as the aluminum radiator. >> -- >> Al Hamilton Those oil lines are probably Teflon covered with braided stainless steel. That is what I have going to the oil cooler. They will last unlike...

Hi Al, it might have been easier for you but it is an extreme fire hazard. If a rubber line splits or cracks it could spray fluid back onto the hot exhaust manifold and it would immediately burst into flames. Transmission fluid is quite flammable. I did not find it difficult to make the tight...

Forgot to say that you should be careful that you don’t drop the nuts down behind the door frame to the floor. You’ll never retrieve them. You can reach through the outside refrigerator vent door to get to the nuts while you file the openings and to hold them in place when you replace the...

You may have to adjust the post out a little. When you loosen the screws will it allow movement outward? If not you can file the metal on the frame a little to allow movement. It probably won’t need much to allow the latch to close around the post Emery Stora 77 Kingsley Frederick CO > > So...

If you ship from the USA it can be labeled “antique auto parts” and there would be no duties or border tax. Emery Stora 77 Kingsley Frederick CO > > Borrmann's Garage in Southern Ontario may be able to help you. He has a few parts coaches and being Canada there is no border hassles. > >...

If you go to Google and put in Atwood He-601 control board you can find many parts that will replace your control board. Emery Stora > > Hi guys, the furnace along with the fridge are not working - I understand that the old furnace would be a problem but majorly pissed off about the >...

Mike you were looking for a valve for your stove. I had written an email some time ago saying that I had located a used one at an RV shop. I didn’t see a reply from you. Do you still need one? Emery Stora emerystora > > Aside from some bad curb rash thanks to lil brother, gf, and a tire shop...

I also once had a dripping pan gasket. It turned out to be a cooler tube on the top left rear of the transmission. You couldn’t see it leaking at idle but the very small leak would run on top of the transmission and down a valley and run around the top of the flange of the pan. I found that a...

to Mike Hamm — I believe that a local RV shop has one on an oven they are parting out. They want $50 for it. Do you have the model number of your stove or a number from the valve so I could check to see if its the right one. It looks like the same stove that is in my 1977 Kingsley. Emery Stora...

You could also easily drill a hole into the manifold and tap it for your sensor. My manifold had a round flat spot on the driver’s side front top which I drilled and tapped for a sensor a few years back when I installed a Digipanel. Emery Stora 77 Kingsley Frederick CO > > years back, I...

I put a thin bead of Permatex Ultra Copper sealant on both sides of my Remflex gasket and it has never blown out. You might try it. Your manifold might have a slight distortion or pitting that could cause the gasket to fail. Two failures and anticipating a third one isn’t normal. Emery Stora...

Do you really lift the engine cover and invite people in for people at a gas station? That’s a lot more than I do. Emery Stora > > Still waiting to paint the aluminum intake manifold before I take the cast iron one off. Advance auto had to order the Duplicolor high temp engine > paint that...

I had an overheating problem about 2 years ago on a fairly recently rebuilt 455 engine. It turned out when the engine overheated two of the center pistons swelled and rubbed on the cylinder walls generating a lot of heat which ruined the engine. I haven’t made a trip with the latest engine...

Silicone spray usually works well. Don’t use WD40 or oil because dust and dirt will stick to it and make sliding even worse. Emery Stora > > lube > > >> Amongst the bigger projects I’m doing on the coach this spring I was reminded of one of the smaller projects I’ve always wanted to get...

Les - When you mount the cabinets to the ceiling you will not have threaded fasteners that are swedged into the ceiling and the other ceiling mounted cabinets use. A good alternative is to use a U-nut. Drill a hole up through the cabinet frame and then reach under the ceiling panel and just...

That is quite a bit different from the one that I built but it would work fine. Mine does not drop below the top of the rear window. Emery Stora emerystora > > Here are plans for the rear window cabinet. > From GMCMI > > https://www.gmcmi.com/wp-content/uploads/2013/02/Rear-Cabinet.pdf > >...

I built a cabinet above the rear windows several years ago. I did not draw up plans but I could. Let me work on it. Meanwhile I’ll send you a picture. I have the bottom just above the window so it doesn’t block the view. For behind the driver if you can find two cabinets from the rear sides...

Sully I know what he said but is it over the rear window, over the stove, over the couch, over the dinette or over the windshield? I have seen them in many positions Emery Stora 77 Kingsley Frederick CO > > Some coaches have as many as 5. They are all different. Which position are > you...