holding tank question

[mark grady]

Tom's post on holding tank hardware has me wondering if anyone has a source
for a holding tank. Mine has been patched beyond hope, an I fear that it
will need to be replaced this year.

Any thoughts from anyone?

Mark Grady

mgrady
'77 K
N Webster, IN

 

[thom hole]

I bought ARDEMCO's holding tank for $225 IIRC. It was an exact
replacement, including the fitting for the sensor

They advertice in GMCMM.

>Tom's post on holding tank hardware has me wondering if anyone has a source
>for a holding tank. Mine has been patched beyond hope, an I fear that it
>will need to be replaced this year.
>
>Any thoughts from anyone?
>
>Mark Grady
>
>mgrady
>'77 K
>N Webster, IN
>

 

[william myers]

ARDEMCO's current price is $278 for holding tank. I believe it is
polyehtlyne not ABS. I just had mine replaced by an RV shop that was
not very familiar with GMCs. They charged a total of $800 using the
ARDEMCO. They claimed it was a lot of work. Been nice to get a real
GMC shop to do it but none around here.

Good luck,
Bill
'74 Glacier, N Tx

> snip
Date: Mon, 25 Jan 1999 09:49:00 -0500
From: Thom Hole
Subject: Re: GMC: holding tank question

I bought ARDEMCO's holding tank for $225 IIRC. It was an exact
replacement, including the fitting for the sensor

They advertice in GMCMM.

>Tom's post on holding tank hardware has me wondering if anyone has a
source >for a holding tank. Mine has been patched beyond hope, an I
fear that it
>will need to be replaced this year.
>
>Any thoughts from anyone?
>
>Mark Grady
>
>mgrady
>'77 K
>N Webster, IN

_________________________________________________________
DO YOU YAHOO!?
Get your free @yahoo.com address at http://mail.yahoo.com

 

[russ bethel]

Try Dale at Sunshine General Store in Castell, TX. His phone number is 915
247-3616. He is very good but he is not cheap. I don't think he is as
expensive as the shop you used. Give him a try. I think you will like him.

Russ Bethel
rbethel

- -----Original Message-----
From: William Myers
To: GMC mailist
Date: Monday, January 25, 1999 10:41 PM
Subject: Re: GMC: holding tank question

>ARDEMCO's current price is $278 for holding tank. I believe it is
>polyehtlyne not ABS. I just had mine replaced by an RV shop that was
>not very familiar with GMCs. They charged a total of $800 using the
>ARDEMCO. They claimed it was a lot of work. Been nice to get a real
>GMC shop to do it but none around here.
>
>Good luck,
>Bill
>'74 Glacier, N Tx
>
>> snip
>Date: Mon, 25 Jan 1999 09:49:00 -0500
>From: Thom Hole
>Subject: Re: GMC: holding tank question
>
>I bought ARDEMCO's holding tank for $225 IIRC. It was an exact
>replacement, including the fitting for the sensor
>
>They advertice in GMCMM.
>

>>Tom's post on holding tank hardware has me wondering if anyone has a
>source >for a holding tank. Mine has been patched beyond hope, an I
>fear that it
>>will need to be replaced this year.
>>
>>Any thoughts from anyone?
>>
>>Mark Grady
>>
>>mgrady
>>'77 K
>>N Webster, IN
>
>
>
>
>_________________________________________________________
>DO YOU YAHOO!?
>Get your free @yahoo.com address at http://mail.yahoo.com
>
>

 

[thomas g. warner]

It is a lot of work Bill should take all of 2 hours to replace. Been there
done that. Go get some money back.

>ARDEMCO's current price is $278 for holding tank. I believe it is
>polyehtlyne not ABS. I just had mine replaced by an RV shop that was
>not very familiar with GMCs. They charged a total of $800 using the
>ARDEMCO. They claimed it was a lot of work. Been nice to get a real
>GMC shop to do it but none around here.
>
>Good luck,
>Bill
>'74 Glacier, N Tx
>
>> snip
>Date: Mon, 25 Jan 1999 09:49:00 -0500
>From: Thom Hole
>Subject: Re: GMC: holding tank question
>
>I bought ARDEMCO's holding tank for $225 IIRC. It was an exact
>replacement, including the fitting for the sensor
>
>They advertice in GMCMM.
>

>>Tom's post on holding tank hardware has me wondering if anyone has a
>source >for a holding tank. Mine has been patched beyond hope, an I
>fear that it
>>will need to be replaced this year.
>>
>>Any thoughts from anyone?
>>
>>Mark Grady
>>
>>mgrady
>>'77 K
>>N Webster, IN
>
>
>
>
>_________________________________________________________
>DO YOU YAHOO!?
>Get your free @yahoo.com address at http://mail.yahoo.com
>
>
>
Tom & Marg Warner
Vernon Center NY
1976 palmbeach

 

[john wright]

At $50 dollars an hour, that 16 hours labor to R&R the tank. Shouldn't
take more that 5 or 6 hours.

Wright

>

>
> > They charged a total of $800 using the
> > >ARDEMCO. They claimed it was a lot of work.
>
> Did they give you a local or were you put to sleep??
> :>)
> Sounds like some of the Onan Guru's of the 3rd kind I've run into.
> Lanier